gemellocattivo.com

Which means "Evil Twin". Lets see your projects where you change boring into fun or create the fun from scratch.
It is currently Sun Sep 21, 2025 12:19 am

Board index » Motor vehicle stuff » Engines

All times are UTC - 5 hours [ DST ]



Post new topic Reply to topic  Page 145 of 271
  [ 2707 posts ]  Go to page Previous  1 ... 142, 143, 144, 145, 146, 147, 148 ... 271  Next
  Print view Previous topic | Next topic 
Author Message
Syscrush
PostPosted: Fri Apr 29, 2022 8:37 pm 
Offline

Joined: Sat Mar 26, 2022 1:39 pm
Posts: 156
Might you get there with a dipstick oil heater and some kind of oil priming setup?
Top
 Profile Send private message  
 
Mehl
PostPosted: Sat Apr 30, 2022 6:08 am 
Offline

Joined: Tue Jan 06, 2015 6:56 pm
Posts: 26
Borrow the heat from heater and pump from your floor heating. Just two tubes to connect instead of radiator needed.
Perhaps use water pump on block, just to find out if leak is from liquid dynamic inside head or block.
Top
 Profile Send private message  
 
mk e
PostPosted: Sat Apr 30, 2022 9:16 am 
Offline

Joined: Thu Jan 01, 2015 6:47 pm
Posts: 4687
I went to the parts store to grab a battery for the mower and the copper spray the website said they had, but when I couldn't find it and asked the counter guy told me he sent it to a shop earlier this morning....we'll call that a sign from Enzo (god of hp) and go with the aviation stuff again I guess.
Top
 Profile Send private message  
 
dcd215
PostPosted: Sat Apr 30, 2022 10:26 am 
Offline

Joined: Thu Mar 24, 2022 7:17 am
Posts: 34
Is it possible that the surfaces are too smooth for the composite gasket to bite ? Googling head gasket materials and surface roughness has some interesting reads .
Top
 Profile Send private message  
 
Syscrush
PostPosted: Sun May 01, 2022 9:43 am 
Offline

Joined: Sat Mar 26, 2022 1:39 pm
Posts: 156
Syscrush wrote:
Might you get there with a dipstick oil heater and some kind of oil priming setup?

Thinking about this further - I believe that a man of your talents could put together a heating element that threads into the oil drain plug. Then use whatever mechanism makes sense to run the oil pump with a drill to circulate that hot oil for as long as you want. Would let you get the engine up to temp from the inside out while leaving the coolant out.
Top
 Profile Send private message  
 
mk e
PostPosted: Sun May 01, 2022 10:24 am 
Offline

Joined: Thu Jan 01, 2015 6:47 pm
Posts: 4687
Syscrush wrote:
Syscrush wrote:
Might you get there with a dipstick oil heater and some kind of oil priming setup?

Thinking about this further - I believe that a man of your talents could put together a heating element that threads into the oil drain plug. Then use whatever mechanism makes sense to run the oil pump with a drill to circulate that hot oil for as long as you want. Would let you get the engine up to temp from the inside out while leaving the coolant out.


or this sure seems easier
Attachment:
heater.JPG
heater.JPG [ 54.21 KiB | Viewed 4422 times ]





I might need 2 but I have a smaller one so I might be able to just switch them side to side a couple times and get it where it needs to go.

I worked on a kitchen cabinet all day yesterday. Honey bunny got a great seal on a fridge that was too tall for the space and I just couldn't find a cabinet shop willing to try and cut down the 24" tall cabinet to 12". It took all day yesterday and into this morning but came out pretty good. I'm guessing now I need to hang it


Attachments:
20220501_102107-resized-1024.jpg
20220501_102107-resized-1024.jpg [ 212.31 KiB | Viewed 4422 times ]
Top
 Profile Send private message  
 
TheDarkSideOfWill
PostPosted: Sun May 01, 2022 12:06 pm 
Offline

Joined: Sat Jan 03, 2015 10:13 pm
Posts: 794
Was that a custom cabinet, so you couldn't just go buy one?
Top
 Profile Send private message  
 
TheDarkSideOfWill
PostPosted: Sun May 01, 2022 12:07 pm 
Offline

Joined: Sat Jan 03, 2015 10:13 pm
Posts: 794
mk e wrote:
Syscrush wrote:
Thinking about this further - I believe that a man of your talents could put together a heating element that threads into the oil drain plug. Then use whatever mechanism makes sense to run the oil pump with a drill to circulate that hot oil for as long as you want. Would let you get the engine up to temp from the inside out while leaving the coolant out.


or this sure seems easier
Attachment:
heater.JPG


I might need 2 but I have a smaller one so I might be able to just switch them side to side a couple times and get it where it needs to go.


Hot water is the way NASCAR teams do it...
Top
 Profile Send private message  
 
mk e
PostPosted: Sun May 01, 2022 1:24 pm 
Offline

Joined: Thu Jan 01, 2015 6:47 pm
Posts: 4687
TheDarkSideOfWill wrote:
Was that a custom cabinet, so you couldn't just go buy one?


Not custom but the both the style and color are discontinued, the manufacturer was the first call I made
Top
 Profile Send private message  
 
mk e
PostPosted: Sun May 01, 2022 1:27 pm 
Offline

Joined: Thu Jan 01, 2015 6:47 pm
Posts: 4687
TheDarkSideOfWill wrote:

Hot water is the way NASCAR teams do it...


That is for sure the safest and most controlled way to do it but I'd like to:
1) NOT put water in it until I know its sealed and
2) Not spend the money or time to build a water heating setup
Top
 Profile Send private message  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 145 of 271
  [ 2707 posts ]  Go to page Previous  1 ... 142, 143, 144, 145, 146, 147, 148 ... 271  Next

Board index » Motor vehicle stuff » Engines

All times are UTC - 5 hours [ DST ]

Who is online

Users browsing this forum: Bing [Bot] and 44 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group